Forum > Windows
New apps based on code revision 2.2 'Noo? No, Ni!' have been released!
Urs Echternacht:
--- Quote from: Urs Echternacht on 22 Feb 2007, 01:20:17 am ---...
Here are some more error reports attached occurring to my dual P3 yesterday. (0xc0000005) Hopefully that flaw can be found someday.
--- End quote ---
Here is my first one of these since i started using 2.2B over a week ago.
[attachment deleted by admin]
Fivestar Crashtest:
--- Quote ---You had probs with Corsair?
--- End quote ---
That was just some ddr400. My XMS ddr2 800 works great.
I am running 5-5-5-15 while I am overclocking, maybe later I will try to tighten the timings. If you are not overclocking, you should be able to run 4-4-4-12 with no problems. I did.
--- Quote ---
Now I let run the PC without the Intel Desktop Utilities prog, because you said that you had probs (freezing) with this (with BOINC too?)...
Maybe that's the reason for my probs...
--- End quote ---
I just didn't like the way the program acted, I was worried it would steal cpu cycles, sitting there in my systray. It seemed to take forever to respond. I don't think it made BOINC crash, or anything.
--- Quote ---
But I'm little confused, because I took (like I said) AIDA32, EVEREST, SpeedFan and MotherboardMonitor and they don't worked with the D975XBX2.
With which prog you look to the complete CPU temp? (not the cores, the "heat-spreader-temp")
Intel Desktop Utilities show me (you too?) only the "temperature range" ("processor thermal margin", that's the heat-spreader?) to the max. temp 65°C? (..on the middle point of the CPU (heat-spreader) QX6700))
(I think, because the man from Intel I called, couldn't tell me what this temp ("processor thermal margin") is ). My experiences, so hotter the CPU so smaller the indicate (idle=50°C, full load=25°C (FanControl ON))
Friendly greetings!
But I'm little bit confused, because with the SSSE3-Core2 Rev. 1.41 I didn't had the probs with freezing BOINC...
--- End quote ---
I guess I am satisfied if it shows me the core temperature. As long as the core isnt' too hot, I am happy. Do they put sensors on the heatspreader? I didn't use Desktop Utilites that long and don't remember "temperature range" or "thermal margin".
When I googled "processor thermal margin", your post here was the top result. I think it must be some kind of engineering term, and your Intel man wasn't an engineer. I don't think it is a temperature, it is a range of temperatures your processor can stand.
If your trouble started when you changed from 1.41 to 2.0 or 2.2, I guess that is what we should look at. From what everyone has said, your processor is not too hot. Maybe you just got a corrupted download of the app. Maybe you could download it again and replace it with a fresh copy. I think the 2.2B apps are doing great, my RAC is still climbing. I don't see why it should be any different for you and it should be better with the QX6700.
Regards,
Pam
CAPTAIN FUTURE:
Hello!
Thanx for your support! :)
I wanted to let run the 4-4-4-12 with the RAMs, but this wasn't function...
After the Power-On Self-Test (POST) I got the message that the actually settings are not good to let run the PC...
I couldn't let him run... he don't wanted... ;)
I musted go back to the "normal" settings (CL5)
When I bought the PC, I said the seller can make the CL4 settings, but to this time with the old BIOS it wasn't possible to let run too... so he called to Intel and the people said that the BIOS must be improved...
I have the newest BIOS... ;)
How you had let it run?
In the BIOS I can select AUTOMATIC - USER - MODE 1 (or like this ;) )
If I select MODE 1 that's the Corsair 4-4-4-12 settings... with 2.1 V
When I let run Intel Desktop Utilities the Windows Task-Manager said that the prog take no CPU-cycles.
If I remember right there is a temp-sensor direct in the middle of the heat-spreader from the CPU.
I let run him all the time with the first copy of Simons app and it's running good now since I terminated the Intel Desktop Utilities...
I don't know, but I will see what will be... :)
At the weekend I changed the heatsink and in the compound manual they say that the first 200 hours the compound need a few circles of cool- hot temps... ON/OFF the PC... so I can let run him 22 hours without probs 2 hours to cool down and then again 22 hours... I will see what will be if I let run him again 24/7... hope he will do the work successful again... :)
@ Simon and/or the optimizer-team
This can be the reason for my probs?
I used:
Intel Desktop Utilities Version 3.0.6.10 and 3.0.10.15
http://www.intel.com/design/motherbd/software/idu/index.htm
I'm not a programmer ;) so maybe if you have time you can look to this software?
CAPTAIN FUTURE:
I am not really amused... :(
*§"%&/(/)/$%"$$"§%*
I had Boinc frozen again... :(
Now I took a new copy of the app and Microsoft .NET V2 and the new Intel Desktop Utilities V3.0.11.16 because I had probs without this prog too...
So... if I have again the probs... then I think I must delete the HDD and make a fresh WinXP to the drive...
Now I don't have updates from the Microsoft homepage, I had only the CD-Rom (WinXP Home SP2) in the drive...
So maybe I must take all the updates from Microsoft to have a good working PC?
(he is running only for S@H, so I don't make safety-relevant work with him...)
Roger the Shrubber:
Bear with me please - I ain't too bright. When I examine my pc I get this: Genuine Intel Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz [x86 Family 6 Model 15 Stepping 6] [fpu tsc pae nx sse sse2 mmx]
I see optimized versions for single cpu sse2 or dual core sse3 but I assume I have a dual core sse2. Why is there not a dual core sse2 - it would probably help if I knew what all that means but heck that would require work on my part!
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version